#
# Acorn Network device configuration
#  These are for Acorn's Expansion card network interfaces
#
config ARM_AM79C961A
	bool "ARM EBSA110 AM79C961A support"
	depends on ARM && ARCH_EBSA110
	select CRC32
	help
	  If you wish to compile a kernel for the EBSA-110, then you should
	  always answer Y to this.

config ARM_ETHER1
	tristate "Acorn Ether1 support"
	depends on ARM && ARCH_ACORN
	help
	  If you have an Acorn system with one of these (AKA25) network cards,
	  you should say Y to this option if you wish to use it with Linux.

config ARM_ETHER3
	tristate "Acorn/ANT Ether3 support"
	depends on ARM && ARCH_ACORN
	help
	  If you have an Acorn system with one of these network cards, you
	  should say Y to this option if you wish to use it with Linux.

config ARM_ETHERH
	tristate "I-cubed EtherH/ANT EtherM support"
	depends on ARM && ARCH_ACORN
	select CRC32
	help
	  If you have an Acorn system with one of these network cards, you
	  should say Y to this option if you wish to use it with Linux.

config ARM_AT91_ETHER
	tristate "AT91RM9200 Ethernet support"
	depends on ARM && ARCH_AT91RM9200
	select MII
	help
	  If you wish to compile a kernel for the AT91RM9200 and enable
	  ethernet support, then you should always answer Y to this.

config ARM_KS8695_ETHER
	tristate "KS8695 Ethernet support"
	depends on ARM && ARCH_KS8695
	select MII
	help
	  If you wish to compile a kernel for the KS8695 and want to
	  use the internal ethernet then you should answer Y to this.

config EP93XX_ETH
	tristate "EP93xx Ethernet support"
	depends on ARM && ARCH_EP93XX
	select MII
	help
	  This is a driver for the ethernet hardware included in EP93xx CPUs.
	  Say Y if you are building a kernel for EP93xx based devices.

config IXP4XX_ETH
	tristate "Intel IXP4xx Ethernet support"
	depends on ARM && ARCH_IXP4XX && IXP4XX_NPE && IXP4XX_QMGR
	select PHYLIB
	help
	  Say Y here if you want to use built-in Ethernet ports
	  on IXP4xx processor.

config W90P910_ETH
	tristate "Nuvoton w90p910 Ethernet support"
	depends on ARM && ARCH_W90X900
	select PHYLIB
	select MII
	help
	  Say Y here if you want to use built-in Ethernet ports
	  on w90p910 processor.

config STM32_ETHER
	tristate "STM32 Ethernet support"
	depends on ARM && (ARCH_STM32 || ARCH_LPC18XX)
	select MII
	help
	  Say Y here if you want to use the built-in Ethernet port
	  on the STM32 processor.

config LPC178X_ETHER
	tristate "LPC178x/7x Ethernet support"
	depends on ARM && ARCH_LPC178X
	select MII
	help
	  Say Y here if you want to use the built-in Ethernet port
	  on the LPC178x/7x processor.

config M2S_ETH
	tristate "SmartFusion2 Ethernet support"
	depends on ARM && ARCH_M2S
	select MII
	help
	  Say Y here if you want to use the built-in Ethernet port
	  on the SmartFusion2 processor

config FM3_ETH
	tristate "FM3 Ethernet support"
	depends on ARM && ARCH_FM3
	select MII
	help
	  Say Y here if you want to use the built-in Ethernet port
	  on the FM3 processor.

config M2S_ETH_RX_NUM
	int "Number of RX buffers in SmartFusion2"
	depends on M2S_ETH
	default "4"
	help
	  Specify the number of RX buffers for SmartFusion2

config M2S_ETH_TX_NUM
	int "Number of TX buffers in SmartFusion2"
	depends on M2S_ETH
	default "4"
	help
	  Specify the number of TX buffers for SmartFusion2

config M2S_ETH_BUF_IN_ESRAM
	bool "Whether SmartFusion2 buffers reside in eSRAM"
	depends on M2S_ETH
	default y
	help
	  Specify Y if you want for the RX / TX buffer and decriptors
	  to reside in the SmartFusion2 embedded SRAM

config M2S_ETH_BUF_IN_ESRAM_BASE
	hex "Base address of SmartFusion2 buffers in eSRAM"
	depends on M2S_ETH_BUF_IN_ESRAM
	default "0x8000"
	help
	  Specify base address of the RX/ TX buffers and descriptors
	  in the SmartFusion2 embedded SRAM
